模板文件为英文。

Safety Harness

SWMS · SWMS-10229

10 个工作步骤
已售出 237 次
版本 7
Working at Height
任何手机都能看

The Safety Harness SWMS sets out the general safety steps, hazards and controls for installing anchor points and using a safety harness. It gives a systematic approach to safety, with best practices, potential risks and recommended controls.

It takes your crew through ten job steps: arrival on site and assessing conditions, training, anchor point set-up, fall arrest system set-up, harness inspection, donning the harness, harness use, emergency response to a fall, incident management, and completion of work and departure.

It suits professionals in construction, telecommunications and any field involving work at heights.

Written by SafetyDocs safety experts, who have been writing safety documents since 2004.

Safety Harness

SWMSVersion 7

Company doing the work: [Company]
Business contact and phone: —
Responsible person (for monitoring SWMS and work): —
Responsible person's phone: —
Responsible person's signature: —
Date signed: —

Principal Contractor (PC): —
PC Address: —
PC phone: —
Date SWMS provided to PC: —
Job Site Address: —
Part of a construction project: —

Site management plan

If the work is part of a construction project, this SWMS must align with the requirements of the Site Management Plan in place for the Construction Project.

High-risk construction work

This work activity involves the following "High-Risk Construction Work" (HRCW - identified in the Job Task column)

FallsInvolves a risk of a person falling from 2m or more, including work on telecommunications towers

Working with a risk of a fall over 2 metres

The fall from height hierarchy of control level considered when establishing controls:

L1Work on the ground or solid construction, not chosen
L2Use a passive fall restraint system, e.g. guard rails, scaffolding, EWP, not chosen
L3Use a work positioning system, e.g. travel restraint, rope access, not chosen
L4Use a fall arrest system, e.g. safety harness, catch platforms, not chosen
L5Implement administrative controls, e.g. signage or instruction, not chosen

No level has been chosen yet.

Planning and preparation

Planning/preparation

Liaise with Principal Contractor to identify on-site safety systems and procedures
Establish supervisory and communication arrangements
Principal contractor to confirm emergency response procedures are in place.

Hold points

Hold points identified and signed off before continuing work. (specify the hold points)

Training/licence

All workers are to have a General Construction Induction Card for construction work.
Relevant workers have relevant certificates of competency, licenses, and training. Specify the SWMS Sign-off for each worker.
Trained First Aider on-site
All workers are trained in site-specific emergency and evacuation procedures, SWMS, safe work procedures, and safety data sheets.

Worker duties and responsibilities

Fit condition for work, i.e., no signs of fatigue, alcohol or drugs
Attend all site inductions/briefings
Comply with all site requirements, e.g. PPE, Traffic Management Plans (TMP)
Only carry out work related to the contract.
Inspect completed work and report possible safety, environmental and quality matters to the supervisor.

Monitor/review

All people involved in the task must have this SWMS communicated to them before work commences.
SWMS is to be reviewed and amended, if necessary, in consultation with relevant people after any near miss or incident
If additional site hazards are identified, review this SWMS and amend control measures to suit
People, including workers, contractors and sub-contractors, affected by the revisions to this SWMS must be informed ASAP.
Give the principal contractor a copy of the revised SWMS
The site supervisor to monitor works against the controls stated in this SWMS
SWMS must be kept on-site and made available for inspection or review
Keep a record of this SWMS until the job is complete or for two years if involved in a notifiable incident
Regardless of any other factor, the person in control of the workplace must review this SWMS at least annually.

Site-specific notes

Legislation and codes of practice

None listed.

Personal protective equipment (PPE)

Foot Protection
Safety Harness

Do not wear rings, watches or jewellery that may become entangled. Long and loose hair must be tied back.

Job steps, hazards and controls

Work activity
Arrival on-site & assess on-site conditions
- Hazard
  Site conditions
  Before controls3 High
  Controls
  - Upon arrival, thoroughly assess the worksite to identify potential hazards (slippery surfaces, overhead obstacles, wind conditions, etc.)
  - Make necessary adjustments to the work plan based on these conditions.
  - If working on EWPs or scaffolding, for this task, ensure there are separate, dedicated EWP/Scaffolding SWMS and that all workers/employees have relevant training and licensing.
  After controls2 Moderate
  Responsible
  - Supervisorto ensure control measures followed
  - Workersto ensure control measures followed
- Hazard
  Contact with electricity
  Before controls3 High
  Controls
  - Ensure no overhead obstructions (such as electric lines).
  - Do not work within No Go Zones of electric lines unless power is isolated and evidence of ongoing isolation is obtained from the electrical supplier.
  After controls2 Moderate
  Responsible
  - Supervisorto ensure control measures followed
  - Workersto ensure control measures followed
- Hazard
  Changing environmental or work conditions
  Before controls3 High
  Controls
  - Working outdoors. Ensure:
    Suitable protective clothing
    Sun brim on hat
    Safety glasses - UV-Rated
    Use 30+ sunscreen on exposed skin areas
    Access to shade during breaks
    Check weather conditions – do not work in extreme weather.
  After controls2 Moderate
  Responsible
  - Supervisorto ensure control measures followed
  - Workersto ensure control measures followed

IR before controls · RR after controls1 LLow2 MModerate3 HHigh4 AAcute

Overall risk after controls2 MModeratethe highest rating after controls

Work activity
Training and Capabilities
Ensure all workers are adequately trained and proficient with the equipment.
Work activity
Anchor point set up
Plan, install and certify the fall arrest anchor points
Work activity
Fall arrest System –Setup
Set up the fall arrest system and check fall clearance
Work activity
Harness Inspection
Review the harness for any potential issues before use.
Work activity
Donning the harness
Fit the harness to the manufacturer's instructions
Work activity
Harness use
Use the harness safely and keep tools secured
Work activity
Emergency response- Fall
Respond to a fall and await rescue
Work activity
Incident Management
Report incidents and learn from them
Work activity
Completion of Work and Departure
Inspect, maintain and store the harness

Permits

Plant and equipment

Hazardous substances

Supervisory arrangements

SWMS Sign-off

This SWMS was developed in consultation and cooperation with workers and relevant organisation representatives. I have read the above SWMS, and I understand its contents. I confirm that I have the skills and training, including relevant certification, to conduct the task as described. I agree to comply with safety requirements within this SWMS, including risk control measures, safe work instructions, and PPE described.

Worker’s name	Job role / positione.g. supervisor, worker, trainee	Licences, competencies & qualificationsType / descriptionClassNumber	Date	Signature
-	-	-	-	-
-	-	-	-	-
-	-	-	-	-
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)
		General construction induction (White Card)

Hierarchy of controls

Risk matrix

Step 1: Determine likelihood

Likelihood	Criteria	Description

Step 2: Determine consequence

Level of effect	Example of each level

Step 3: Determine the risk score

Likelihood ↑	InsignificantNo effect, or so minor that the effect is acceptable	MinorMinor first aid treatment, minimal business disruption, minimal environmental effect	ModerateSerious injuries, medium business interruption, medium environmental impact	MajorExtensive injuries or fatality, significant business interruption, environmental harm, prosecution	CatastrophicMultiple permanent disabilities or fatalities, business failure, substantial environmental harm, prosecution or imprisonment
	Consequence →
Almost certainExpected in most circumstances	2 Moderate	2 Moderate	3 High	4 Acute	4 Acute
LikelyWill probably occur in most circumstances	2 Moderate	2 Moderate	3 High	4 Acute	4 Acute
PossibleCould possibly occur at some time	1 Low	2 Moderate	2 Moderate	3 High	4 Acute
UnlikelyUnlikely but possible	1 Low	1 Low	2 Moderate	3 High	4 Acute
RareHighly unlikely to occur	1 Low	1 Low	2 Moderate	2 Moderate	3 High

1 LowRecord and monitor. Proceed with work, and review the risks regularly.
2 ModerateMaintain control measures. Be cautious when working, and monitor and review regularly.
3 HighReview before commencing work. Introduce new controls or maintain high-level controls to lower the risk level, and monitor the controls frequently.
4 AcuteDo not proceed until the risk level is reduced. Immediately introduce high-level controls, and re-assess before proceeding.

Step 4: Record risk

Score	Action

还有 9 个工作步骤，从“Training and Capabilities”到“Completion of Work and Departure”

每一步都有危险、风险等级和控制措施，另附工人签到。

免费试用编辑器获取这个模板

在浏览器中的样子

获取这个模板

免费注册，然后选择获取方式。你的公司信息会自动填好。

付费套餐包含
使用套餐中的模板额度。这一份需要 1 个额度。
比较套餐和价格
单独购买
$89.95 一次付清，永久归你。免费套餐也能用。

免费试用编辑器免费注册

注册无需银行卡。抢先体验会员购买任何套餐都可享 30% 折扣。

涵盖内容

10 个工作步骤

Arrival on-site & assess on-site conditionsCheck the site conditions before beginning any task.
Training and CapabilitiesEnsure all workers are adequately trained and proficient with the equipment.
Anchor point set upPlan, install and certify the fall arrest anchor points
Fall arrest System –SetupSet up the fall arrest system and check fall clearance
Harness InspectionReview the harness for any potential issues before use.
Donning the harnessFit the harness to the manufacturer's instructions
Harness useUse the harness safely and keep tools secured
Emergency response- FallRespond to a fall and await rescue
Incident ManagementReport incidents and learn from them
Completion of Work and DepartureInspect, maintain and store the harness

涵盖的危险

评价

29 May 2014
Thankyou! It helped greatly It helped us in developing our own SWMS. This was fantastic in setting up a base and for us to develop on. It had everything we needed including all relevant codes of practice!
Brittany已验证购买